Compact Infrared Conveyor Dryer
Cures Oversized Screen Printed Garments
and DTF Adhesives
The D-1000 compact infrared heating model comes with 26 in. (66.1 cm) wide belt and 56 in. (142.2 cm) long conveyor belt, with a 25 in. (63.5 cm) infeed as standard. An optional 10 inch conveyor extension is available if desired. A 27.75 in. (70.5 cm) wide chamber infeed allows for loading of heavier and larger garments.
Also optional is a powered exhaust hood to remove moisture and fumes from the heating chamber — critical for rapid drying of water-based inks and discharge, and curing of DTF adhesives.
At 56 in. (142.2 cm) long and 32 in. (81.3 cm) wide overall, the unit fits on tabletops or on utility carts with tops as small as 30 in. (76.2 cm) square, and is available with an optional mobile stand. It is also suitable for mobile screen printers to power on site using a small generator at fairs, concerts, trade shows and other events where larger garments as well as tees may be screen printed.
It is available in 120V or 240V models equipped with a 20 in. (50.8 cm) wide by 16 in. (40.6 cm) long, 2050 watt heater that carries the same 15-year warranty as all Vastex infrared heaters.
Variable controls for both heat intensity and conveyor speed allow fine-tuning of the drying process according to ink type, ink coverage, desired cure temperature, and rate at which items are being screen printed, or coated with DTF adhesives.
The heater can be raised, lowered and pivoted using lock knobs on the sides of the heating chamber according to the thickness of printed garments and/or the angle of printed images on irregularly shaped items, for uniform curing of the printed area using minimum energy. Heater shields are included as standard to maximize edge-to-edge temperature consistency for increased image quality.
The compact unit is CE certified and shippable worldwide via UPS, FedEx, DHL and other small package carriers.
REQUIRED RECEPTACLE
D-1000
5-20P
D-1000-240
6-15P
Hi/Lo heat adjustment and variable belt speed give you full control.
The D-1000 has a tilting heater design which works great for curing hats or mugs.
SMART
Teflon coated fiberglass belt with tracking system
BELT WIDTH
(max garment width)
26" (66 cm)
HEATER WIDTH
20" (51 cm)
ADJUSTABLE
Speed, temperature, heater height and tilt
FAST
110+* shirts per hour with plastisol and 50+* with discharge
PRECISE
Powerful infrared heater with tight coil pattern and heat shields
VALUABLE
Best warranty, high quality, exceptional service
COMPACT
Total footprint is about 12.5 sq. ft (1.2 sq. m).
EXTENDABLE
Optional 10" front conveyor extension
OPTIONS
- 10" (25.4 cm) front conveyor extension
- Optional powered exhaust removes moisture and fumes — ideal for working in confined spaces.
- Exhaust hood (EXH-18)
- Optional stands with wheels
*Cure times are 25% below actual test results. Production may vary based on ink, environment and other variables.
Click on the blue Live Chat tab on the right to speak to a Vastex representative.
(Available daily 9:00 AM - 5:00 PM EST, Monday - Friday)
Or click here to REQUEST A QUOTE >>
OPTIONAL ACCESSORIES
CONVEYOR EXTENSIONS & ADDITIONAL CHAMBERS
Vastex Conveyor Extensions make it easy to increase production without buying an entirely new dryer. Extensions can be used to increase the infeed, outfeed, or add additional heat chambers. With bolt-on installation and conveyor belt extensions, your dryer can be upgraded quickly and easily.
Available belt sizes:
- 18 x 18 in. (45.7 x 45.7 cm)
- 18 x 36 in. (45.7 x 91.4 cm)
- 30 x 18 in. (76.2 x 45.7 cm)
- 30 x 36 in. (76.2 x 91.4 cm)
- 30 x 54 in. (76.2 x 137.2 cm)
- 54 x 18 in. (137.2 x 45.7 cm)
- 54 x 36 in. (137.2 x 91.4 cm)
- 54 x 54 in. (137.2 x 137.2 cm)
- 78 x 36 in. (198 cm x 91.4 cm)
- 78 x 54 in. (198 cm x 137.2 cm)
INCREASING CAPACITY OF A VASTEX CONVEYOR DRYER
with additional heating chamber and conveyor belt extension
See it in action!
EXHAUST HOOD
- Exhaust booster system reduces fumes at exit of dryer (a "must have" for DTF adhesives on D1-Series and LR-X1)
- Independent power and control
- Snap ON or OFF for easy mobility and maintenance
- Diagnostic pilot light and ON/OFF switch
- Optional adjustable conveyor mount available
Model EXH-18
For dryers with belt width of 18 to 30 in. (46 to 76 cm)
- 141 cfm, 2.1 amps, NEMA 5-15P plug
- 141 cfm, 1.0 amps, NEMA 6-15P plug
Model EXH-30
For dryers with belt width of 24 to 36 in. (61 to 91 cm)
- 141 cfm, 2.1 amps, NEMA 5-15P plug
- 141 cfm, 1.0 amps, NEMA 6-15P plug
Model EXH-54
For dryers with belt width of 48 to 60 in. (122 to 152 cm)
- 300 cfm, 1.0 amps, NEMA 6-15P plug
POWERED EXHAUST
Optional powered exhaust removes moisture and fumes — ideal for working in confined spaces.
POWERED EXHAUST
Optional powered exhaust removes moisture and fumes — ideal for working in confined spaces, especially when curing of DTF adhesives.
SIDE HEATERS
Side-mounted heaters can be added to any model, and come as standard on deluxe models.
- Positioned at a 45 degree angle
- Controlled from the main panel
- Available in single or three phase dryers and in 240, 380, and 480 V
- Each heater is 1,400W adding a total of 2,800W
- Digital timer adjusts heat output from 0 to 100%
- Increases "cure zone" to 24 in. on 30 in. belts
- Increases "cure zone" to 48 in. on 54 in. belts
- Side heaters can be tilted from 40 - 50 degrees to suit application
- The addition of side heaters changes the heater height adjustment range from 2 - 7 in. (5 - 17.8 cm) to 4 - 7 in. (10 - 17.8 cm)
CONVEYOR AIR BAR
- Speeds the cooling of screen-printed and inkjet-printed garments, caps, koozies, umbrellas and hard goods as they exit a dryer's heating chamber, rapidly cooling/hardening hot ink that is soft or tacky, and making printed items easy to fold or package.
- Houses tightly-spaced mini fans providing uniform airflow across the printed item, angled outward to avoid blowing cool air into the heating chamber.
- Height adjustable to accommodate thin to bulky items.
- Independent power
Model CAB-30 houses five fans, and adjusts to fit any Vastex or other dryer having a 33 to 39 in. (83.8 to 99 cm) wide conveyor. A CAB-30-240 model is available for 240V systems.
Model CAB-54 includes nine fans and fits any Vastex or other dryer with a 57 to 63 in. (144.8 to 160 cm) wide conveyor. A CAB-54-240 model is offered for 240V systems.
CAB-30
- 5 fans across unit
- Vastex: 30 in. (76 cm) wide belt dryers
- Non-Vastex: 33 to 39 in. (83.8 to 99 cm) outside conveyor width
- CAB-30-240 for 240v model
CAB-54
- 9 fans across unit
- Vastex: 54 in. (137 cm) wide belt dryers
- Non-Vastex: 57 to 63 in. (144.8 to 160 cm) outside conveyor width
- CAB-54-240 for 240v model
CAB-78
- 12 fans across unit
- Vastex: 78 in. (198 cm) wide belt dryers
- Non-Vastex: 81 to 87 in. (206 to 221 cm) outside conveyor width
- CAB-78-240 for 240v model
RETURN BELT CONVEYOR
- Returns cured garments to the front of the dryer while they cool, ready for folding and packaging
- Allows conveyor dryer to be positioned closer to a wall without the need of a catch bin, saving space
- Positioned between two presses, shops can print the front with one press and print the back with the second press as the garment comes back off the return conveyor
- Available for LittleRed, Little Red D Series and EconoRed dryers with 30, 54 or 78 in. (76, 137 or 198 cm) wide belts
- Can also be added as a retrofit to many existing dryers
HAT SUPPORT RAIL
HR-1 Hat Support Rail
(fits EconoRed ER-II dryers)
HR-2 Hat Support Rail
(fits BigRed BR4D and ER-III dryers)
- Easily mounts to the interior of dryer
- Stationary rail for hats to leans against. This allows the front of the hat to be parallel to heating elements.
HEAVY DUTY WHEEL SET
Model WS-EC
Standard Wheel Set
- Set of 4 fits all DriBox, LittleRed, EconoRed and BigRed dryers with 30 or 54 in. (76 or 137 cm) belt widths only
- Single caster under leg will raise the dryer an additional 4 in. (10.16 cm) off of the ground. Makes moving the dryer easy for rearranging or cleaning your shop.
Model WS-E-DD
Heavy Duty Drop-Down Wheel Set
- Set of 4 fits all DriBox, LittleRed and EconoRed I dryers with 30, 54 or 78 in. (76, 137 or 198 cm) belt widths
- Sturdy casters on each side of the leg with a bracket in between. Will only raise the dryer ½ in. (1.27 cm) off of the ground. Makes moving the dryer easy for rearranging or cleaning your shop.
HEAVY DUTY WHEEL SET
Model WS-EC
Standard Wheel Set
- Set of 4 fits all DriBox, LittleRed, EconoRed and BigRed dryers with 30 or 54 in. (76 or 137 cm) belt widths only
- Single caster under leg will raise the dryer an additional 4 in. (10.16 cm) off of the ground. Makes moving the dryer easy for rearranging or cleaning your shop.
Model WS-EHD
Heavy Duty Drop-Down Wheel Set
- Set of 4 fits all BigRed and EconoRed II & III dryers with 30 or 54 in. (76 or 137 cm) belt widths only
- Sturdy casters on each side of the leg with a bracket in between. Will only raise the dryer ½ in. off of the ground. Makes moving the dryer easy for rearranging or cleaning your shop.
MOBILE EQUIPMENT STANDS, INCLUDING CASTERS
Low Cost Stands for "tabletop" infrared conveyor dryers, screen exposing units and other screen printing equipment.
Model S1-27
- Flat top to fit Vastex D100 Conveyor Dryer, and can also accommodate other compact tabletop equipment weighing up to 250 lb (113 kg).
- 26.8 in. (68 cm) H x 32.3 in. (82 cm) W x 32.3 in. (82 cm) D
- 55 lbs (25 kg)
- Shippable via UPS
Model S1-27-DEMT
- Rail mounts fit Vastex E-200 Exposing Units, and D-1000 Conveyor Dryers
- Can also accommodate other compact tabletop equipment weighing up to 250 lb. (113 kg)
- 27.4 in. (70 cm) H x 32.1 in. (82 cm) W x 30.6 in. (78 cm) D
- 60 lbs (27.2 kg)
- Shippable via UPS
ATKINS THERMAL PROBE COMPLETE KIT
(Includes controller, probe and extra wires)Accurately measure ink temperatures to profile conveyor dryers
- Constructed of temperature-resistant Teflon®, it may be used hundreds of times with-out degradation of material or accuracy of measurement.
- The wires are designed to make DIRECT CONTACT WITH THE INK. Many other temperature measuring devices are capable of reading only the temperature of the air around the screen printed item. The rise and fall of the ink temperature may be significantly different than that of the garment or the surrounding air.
- Response Time: 1 second, in liquid
- Auto Shut-off: Auto shut-off after 10 minutes of non-use
- Warranty: 5 year instrument warranty, 1 year probe
- Cable Length: 15 ft cable with Silicone outer jacket
- Certifications: NSF, CE, Rohs, Weee
- Temperature Range: -40° to 400°F (-40° to 205°C) with probe
- Temperature Accuracy: ±0.5F° (±0.3C°) over entire range at ambient temperatures between 68° to 86°F (20° to 30°C)
- Resolution: 0.1°
- Waterproof Rating: IPX7 Waterproof-rated
- Battery Life: 1800 hours typical, 2 AAA Alkaline batteries (included)
THE IMPORTANCE OF USING A DONUT PROBE
See it in action!
Testing Ink Temperatures
With the thermometer on and probe plugged in, place the "ring" over an inked part of a garment (or scrap piece of material) with the cross-hairs wires down. Be sure the wires are actually touching the ink. Allow the garment and probe to be fed into the dryer along the conveyor belt. The temperature displayed by the thermometer reflects the rise in temperature of the ink as it moves through the dryer. When the temperature begins to quickly decline, the probe should now have exited the dryer. Unplug the probe and allow only the lead wire to follow the probe through the dryer. DO NOT ALLOW THE THERMOMETER TO GO THROUGH THE DRYER and DO NOT PULL RING BACK as this could damage the delicate cross-hair wires.
SCREEN PRINT DONUT PROBE
The "Donut" Screen Printing Probe is specially designed to meet the needs of today's Screen Printers.
- Constructed of temperature-resistant Teflon®, it may be used hundreds of times with-out degradation of material or accuracy of measurement.
- The wires are designed to make DIRECT CONTACT WITH THE INK. Many other temperature measuring devices are capable of reading only the temperature of the air around the screen printed item. The rise and fall of the ink temperature may be significantly different than that of the garment or the surrounding air.
- Type K thermocouple surface probe for monitoring the temperature of ink or screen printing dryers
- Measures temperature from -40° to +400°F (-40° to +205°C)
- PTFE ring 3 in. (7.6 cm) in diameter supports the sensor wires
- Response time of 1 second in liquid for fast readings
- Warranty - 1 year
- Silicone-jacketed cable 15 ft (457 cm) in length withstands temperatures up to 400°F (205°C)
TEMPERATURE LASER GUN
Measures temperature of ink and/or substate.
- Measures temperatures from 0F to 716°F (-18°C to 380°C) with typical accuracy of +/- 2%
- Fixed emissivity: 0.95
Please note that a temperature gun "only" measures the surface temperature. For the most accurate results, a donut probe is highly recommended.
